Project Overview

You can keep all your bikes and cycling gear together with this simple D.I.Y. multiple bike rack. We’ll show you how to make a rack for storing all kinds of bikes, scooters, helmets and bike pumps. Continue to step-by-step instructions

Step by Step Instructions

1 Have your timber pre-cut
2 Lay-out the base frame
3 Secure the base frame
4 Lay-out and build the top frame
5 Attach the mid-rail
6 Attach the pegboard
7 Measure and mark for the galvanised pipes
8 Drill the holes for the pipes
9 Screw in the pipes
10 Join the two frames
11 Secure the support beam to the frame
12 Sand and paint the bike rack
  • Step 1. Have your timber pre-cut

    You can make your bike rack to suit how many bikes and cycling gear you need to store. We had our timber pre-cut at Bunnings to these lengths:

    45mm x 90mm x 820mm pine x 6
    45mm x 90mm x 1000mm pine x 2
    45mm x 90mm x 625mm pine x 2

  • Step 2. Lay-out the base frame

    The main components of the bike rack are the two pine frames, which are held together with bugle bolts and two brackets. To build the base frame, take two 820mm pieces of pine and lay them horizontally on a flat surface. Lay the two shorter 625mm pieces between these for the sides to create a rectangular-shaped frame. Make sure all the corners are square.
  • Step 3. Secure the base frame

    With your base frame square, use the 9mm drill bit to pre-drill through the 625mm timbers into the longer timbers. Use two bugle 125mm screws in each corner to secure the base frame together.

  • Step 4. Lay-out and build the top frame

    Simply repeat the previous two steps to make the top frame. Build a rectangle out of the two lengths of timber. Using the same 9mm bit, pre-drill through the longer timbers into the shorter timbers. Secure the frame with 2 x 125mm bugle screws in each corner.

  • Step 5. Attach the mid-rail

    Next you need to make a mid-rail, which will be used to attach the peg board. Measure the height of the pegboard, ours was 445mm. Then transfer these measurements to the longer side vertical timber on the top frame. These marks are the fixing point for the mid-rail. Put the mid-rail in position, make sure it’s square and use the 125mm bugle screws to screw it into place.

  • Step 6. Attach the pegboard

    Lay the peg board on the top frame, make sure it’s flush with the top of the frame and the mid-rail. Use the 20mm screws to attach the peg board to the frame. Don’t worry if the board burrs where you insert the screws, these can be sanded back later. 

  • Step 7. Measure and mark for the galvanised pipes

    The galvanised pipes are what will hold the front wheels of your bike, so make sure you space them the right distance apart. Place the top piece of 625mm timber onto the bottom frame and measure and mark out where you want the pipes to go. Mark a quarter of the way in (205mm) and three quarters (615mm) of the way in. Transfer these measurements onto the bottom frame with your pencil and T-square.

  • Step 8. Drill the holes for the pipes

    Use the 20mm spade bit to drill four holes for the galvanised pipes. Make sure you drill them on an angle so the galvanised pipe line up with the holes in the timber on the base. Only drill deep enough to cover the thread on the pipe.
  • Step 9. Screw in the pipes

    Insert the galvanised pipes into the holes in the base of the frame. Then insert them into the holes that will be attached to the top frame. You may need to make your holes a little deeper if this piece of timber does not fit into place properly.
  • Step 10. Join the two frames

    Stand the bottom frame upright and slide the top frame next to it. Make sure the frames are square and then screw in the two brackets to join them together.
  • Step 11. Secure the support beam to the frame

    Secure the top piece of timber with the galvanised pipes. Tap this beam into place and measure to make sure that it’s flush and square. Screw it into place with 2 x 125mm bugle screws on each side.
  • Step 12. Sand and paint the bike rack

    Now the bike rack is built, sand it using 120 grit sandpaper. You can then paint it the colour of your choice. Now it’s in place, it looks great and is keeping the kids bikes neat and tidy.

Tools and Materials

Tools

  • Cordless screwdriver or impact driver
  • 20mm spade bit
  • 9mm wood drill
  • 6mm hex bit
  • Drop sheet
  • Earmuffs
  • Hammer
  • Marker
  • Paint brush
  • Phillips head bit
  • Pencil
  • Paint tin opener
  • Plastic wood scraper
  • Safety glasses
  • T-square

Materials

  • 45mm x 90mm x 820mm pine x 6
  • 45mm x 90mm x 625mm pine x 2
  • 45mm x 90mm x 1m pine x 2
  • 1000mm x 445mm x 3mm pegboard
  • 16mm x 600mm galvanised pipe x 4
  • 400mm x 350mm x 25mm metal brackets x 2
  • Timber screws for brackets
  • 20mm pin board
  • 125mm timber bugle screws x 25
  • 120 grit sandpaper
  • Hooks or hanging fixtures
  • Paint or stain
garage

Tools & Skills Seven handy tool storage ideas Keeping your tools safe, secure and in easy reach makes it so much easier to get your projects done. Whether you need tool storage for work or around the home, there’s a huge range of handy options in all shapes and sizes.

How to restore wooden furniture 03:36

Tools & Skills How to restore wooden furniture If you’ve got old wooden furniture that’s seen better days, you’d be surprised how easy it is to restore it and give it a new lease of life

install hinges and gass struts

Tools & Skills Five cordless power tools that will make your D.I.Y. projects easier Cordless power tools offer you the flexibility and freedom to work just about anywhere. They’re portable, light weight and easy to handle. Here are our top five cordless tools that will help make your D.I.Y. dreams a reality.

circular saw

Tools & Skills Five things you need to know before selecting any power tool If you’re looking for a new power tool, there are few terms you need to know that may influence which one you buy. Here’s a look at five of the most common things you’ll hear when you’re out shopping for power tools.

Man measuring project 01:57

Tools & Skills How to calculate square metres Learn how to calculate in square metres to make sure you order enough materials for your renovations and D.I.Y. projects.

Selection of tools 03:41

Tools & Skills How to choose tools for your toolbox Check out this list of basic tools that are great for every toolbox.

Man using small step ladder 03:10

Tools & Skills How to use a ladder correctly Ladders are very useful, but it’s important to keep safe and use them correctly. We show you how to use three different ladders properly.

Person rubbing steel wool over hammer 02:42

Tools & Skills How to clean rusty tools We’ll show you how to restore your rusty tools.

Top of the content