D.I.Y. room divider

tracy

Project Overview

Bunnings magazine, July 2019

Unassuming at first glance, dressed timber battens can be the basis for room-changing projects. Try this dividing screen if you have an open-plan space.

Continue to step-by-step instructions

Step by Step Instructions

1 Make the slats and rails
2 Position the slats
3 Drill holes into the slats
4 Secure to the top and base rail
5 Centre and secure a middle rail
6 Fill, sand and paint
7 Lock it in
  • Step 1. Make the slats and rails

    To make the vertical slats, measure and mark eight lengths of 65mm dressed oak to 2.1m, cutting to length with a mitre saw. To make the top and base horizontal rails, cut the remaining 65mm piece into two 751mm lengths. For the middle horizontal rails, cut the 40mm dressed oak into three lengths of 751mm.

    Tip: While you could make the cuts using a mitre box with a hand saw, a mitre saw will result in much faster, more accurate assembly.

  • Step 2. Position the slats

    Position a length of painter's masking tape along the top, base and middle rails to mark out the position of the slats, measuring along the top rail first, marking 65mm from the edge, then 33mm, and repeating to the end. Transfer the measurements to the other rails using the combination square.

    Tip: The room divider is designed to be 2.1m high and exactly 751mm wide, which allows for the vertical slats to be placed 33mm apart.

  • Step 3. Drill holes into the slats

    Mark a centre line along the top and base rails (32.5mm from the edges), and along the middle rails (20mm from the edges). Use a 2.5mm bit to drill pilot holes along the lines, evenly spacing two holes into each slat.

  • Step 4. Secure to the top and base rail

    Working on a large, flat surface, set out the slats under the top and base rails, lining them up with the marks. Begin at one end, checking the first slat is flush and square with the top rail, and secure with two 20mm screws using a drill with a driver bit. Check the slat is flush with the base rail and secure, then repeat with the remaining rails.

  • Step 5. Centre and secure a middle rail

    On the slats at either end, measure and mark 1050mm from the base to centre a middle rail, securing with screws. Mark the end slats 40mm either side of the first middle rail and secure remaining rails.

  • Step 6. Fill, sand and paint

    Use a spatula to fill screw heads with timber filler, leave to dry. Sand all over, wipe with a damp cloth, then finish with primer and two coats of paint using a mini roller, leaving to dry between coats.

    Tip:To hide the brackets, spray-paint them in a matching colour before attaching.

  • Step 7. Lock it in

    Mark out where the divider will stand. Position one bracket on the floor against the wall, secure into both with anchors and screws. At the top, attach a bracket so one arm is against the wall and the other is over the top of the divider, secure with screws. Secure a third bracket halfway up the divider, against the wall. Attach the fourth bracket to the floor with one arm facing upwards so the divider sits inside it, securing from the outside with a screw.

Tools and Materials

Tools

  • Safety equipment
  • Measuring tape
  • Marker pen
  • Mitre saw
  • Combination square
  • Cordless drill
  • Mini roller and tray
  • 50mm stainless steel angle (L) brackets (pack of four)

Materials

  • 2.5mm drill bit
  • Driver bit
  • Nine 2.4m lengths 65mm x 12mm dressed oak
  • 2.4m length 40mm x 12mm dressed oak
  • 6G x 20-25mm timber screws
  • Timber filler and spatula
  • Sanding block with 180-grit abrasive paper
  • Painter's masking tape
  • 500ml 3 in 1 primer sealer undercoat
  • Interior low sheen paint
  • Wall anchors for your wall type
hydrangea

Planting & Growing How to create an allergy-friendly garden If you suffer from hay fever or other allergies, then being out in the garden can, at times, be less than enjoyable. But there are some steps you can take to create an allergy-friendly garden so you can spend more time gardening and less time sneezi...

pallet coffee table

Outdoor Living Five D.I.Y. ideas to update your outdoors Autumn is a great time of the year to tick off a few D.I.Y. projects from your to-do list. Here are a few good ideas to get you started.

pot

Planters How to choose the right plant pot Pots are a great way to add colour, interest or texture to your outdoor space. Tuscan Path’s Elaine Foster shares her top tips on how to choose the perfect pot.

sunflower

Planting & Growing How to plant and care for sunflowers Sunflowers are a great way to add colour to your garden, and they’re easy to grow and care for. Bunnings Greenlife buyer Katie explains the basics of how to grow sunflowers and shares some tips on how to care for them.

orchid

Planting & Growing How to care for orchids Orchids are a low-maintenance flower that can be grown indoors or outside in a protected location. And, with a little care, they will provide you with lots of colour.

paint

Guides & Projects How to upcycle almost any piece of furniture with paint Rather than throwing out old household items, you can restore them with paint. It’s a quick, easy and affordable way to give anything from furniture to fences a new lease on life. Learn how to paint and prepare different surfaces to get the finish y...

DIY balcony and courtyard garden

Planters D.I.Y. balcony and courtyard garden Even if your outdoor space is limited to a balcony or courtyard, it doesn’t mean you have to miss out on having a garden. The team at Tuscan Path, who have been supplying pots to the Australian marketplace for over 40 years, share some ideas on how ...

 kitchen benchtop materials

Benchtops & Cabinets A guide to kitchen benchtop materials The perfect benchtop will add style to any kitchen. It’ll also see the most action, so choosing the right benchtop for your kitchen – and budget – is an important decision explains Bunnings Kitchen Designer Ben Carey.

Top of the content